Enhanced CO2 Capture of Poly(amidoamine)-Modified Graphene Oxide Aerogels with the Addition of Carbon Nanotubes.

Innovative dendrimer-modified graphene oxide (GO) aerogels are reported by employing generation 3.0 poly(amidoamine) (PAMAM) dendrimer and a combined synthesis approach based on the hydrothermal method and freeze-casting followed by lyophilization. The properties of modified aerogels were investigated with the dendrimer concentration and the addition of carbon nanotubes (CNTs) in varying ratios. Aerogel properties were evaluated via scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). The obtained results indicated a strong correlation of the N content with the PAMAM/CNT ratio, where optimum values were revealed. The CO2 adsorption performance on the modified aerogels increased with the concentration of the dendrimer at an appropriate PAMAM/CNT ratio, reaching the value of 2.23 mmol g-1 at PAMAM/CNT ratio of 0.6/0.12 (mg mL-1). The reported results confirm that CNTs could be exploited to improve the functionalization/reduction degree in PAMAM-modified GO aerogels for CO2 capture.

Chemical Modification of Agro-Industrial Waste-Based Bioadsorbents for Enhanced Removal of Zn(II) Ions from Aqueous Solutions.

Contamination of water by heavy metals is a major environmental concern due to the potential ecological impact on human health and aquatic ecosystems. In this work, we studied the chemical modification of various fruit peels such as banana (BP), granadilla (GP), and orange ones (OP) in order to obtain novel bio-adsorbents to improve the removal of Zn(II) ions from 50 mg·L-1 synthetic aqueous solutions. For this purpose, sodium hydroxide and calcium acetate were employed to modify the fruit peels. The moisture, extractives, lignin, hemicellulose, and cellulose contents of the raw materials were determined according to ASTM standards. The obtained bio-adsorbents were characterized by scanning electron microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR) and thermogravimetric analysis (TGA). The results showed the OP bio-adsorbents performed better, especially when the concentration of the modifier solutions increased, e.g., the OP particles modified using 0.8 M NaOH and Ca(CH3COO)2 solutions resulted in 97% removal of Zn(II) contaminating ions and reached a maximum adsorption capacity of 27.5 mg Zn per gram of bio-adsorbent. The adsorption processes were found to follow a pseudo-second order model. The error function sum of square error indicated the Freundlich isotherm (non-linear regression) as best fit model. The obtained results are particularly interesting for material selection in wastewater treatment technologies based on contaminant adsorption.

Graphene Oxide-Polypyrrole Coating for Functional Ceramics.

Ceramic substrates were metallized with a Ni-Mo-P electroless coating and further modified with a polypyrrole (PPy) coating by the electrodeposition method. The properties of the polypyrrole coating were studied with the addition of a graphene oxide (GO) nanomaterial prior to the electrodeposition and its reduction degree. Fourier Transform Infrared Spectroscopy, Field-Emission Scanning Electron Microscopy, Raman spectroscopy and cyclic voltammetry were employed to characterize the properties of the coatings. The results indicated the successful synthesis of conductive electrodes by the proposed approach. The electrodeposition of PPy and its charge storage properties are improved by chemically reduced GO. The surface capacitive contribution to the total stored charge was found to be dominant and increased 2-3 fold with the reduction of GO. The chemically reduced GO-modified PPy exhibits the highest capacitance of 660 F g-1 at 2 mV s-1, and shows a good cyclability of 94% after 500 charge/discharge cycles. The enclosed results indicate the use of an NiMoP electroless coating, and modification with a carbon nanomaterial and conducting polymer is a viable approach for achieving functional ceramics.

Effect of Deposition Parameters on Electrochemical Properties of Polypyrrole-Graphene Oxide Films.

Graphene oxide (GO)-modified polypyrrole (PPy) coatings were obtained by electrochemical methods in the presence of the anionic surfactant, sodium dodecyl sulfate (SDS). The structure, morphology, and electrochemical properties of the coatings were assessed by Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM) and cyclic voltammetry at varying scan rates, respectively. The properties of the obtained coatings were analyzed with the GO and PPy loadings and electrodeposition mode. The hybrid coatings obtained galvanostatically showed a coarser appearance than those deposited by cyclic voltammetry CV mode and improved performance, respectively, which was further enhanced by GO and PPy loading. The capacitance enhancement can be attributed to the SDS surfactant that well dispersed the GO sheets, thus allowing the use of lower GO content for improved contribution, while the choice of suitable electrodeposition parameters is highly important for improving the applicability of GO-modified PPy coatings in energy storage applications.

The Effect of Solvothermal Conditions on the Properties of Three-Dimensional N-Doped Graphene Aerogels.

Low-density three-dimensional (3D) N-doped graphene aerogels by a one-step solvothermal method in the presence of ethylenediamine (EDA) are reported. The gelation, formation, and properties of the aerogels were studied with solvothermal conditions, namely, operating temperature, time, graphene oxide (GO) concentration, and the GO/EDA w/w ratio. Two ranges of solvothermal conditions are employed: one involving an operating temperature below 100 °C and a conventional chemical reduction of GO with EDA at atmospheric pressure and a second one employing a higher temperature range up to 165 and a high pressure reduction with EDA. The results show that both solvothermal approaches allow for the fabrication of homogeneous N-doped 3D graphene aerogels with density values close to 10 mg cm-3. The measurements indicated that low values of GO concentration, temperature, and EDA are optimum for obtaining low-density 3D aerogels. N doping is improved with an EDA amount in lower temperature conditions. The N doping mechanism below 100 °C is dominated by the epoxy ring opening while at temperatures up to 165 °C both epoxy ring opening and amidation take place. The CO2 adsorption properties are strongly controlled by the nitrogen configuration, namely, pyridinic nitrogen in terms of its density.

In vitro and environmental toxicity of reduced graphene oxide as an additive in automotive lubricants.

Despite the ground-breaking potential of nanomaterials, their safe and sustainable incorporation into an array of industrial markets prompts a deep and clear understanding of their potential toxicity for both humans and the environment. Among the many materials with great potential, graphene has shown promise in a variety of applications; however, the impact of graphene based products on living systems remains poorly understood. In this paper, we illustrate that via exploiting the tribological properties of graphene nanosheets, we can successfully improve both the frictional behaviour and the anti-wear capacity of lubricant oil for mechanical transmission. By virtue of reducing friction and enhancing lubricant lifetimes, we can forecast a reduction in friction based energy loss, in addition to a decrease in the carbon footprint of vehicles. The aforementioned positive environmental impact is further strengthened considering the lack of acute toxicity found in our extensive in vitro investigation, in which both eukaryotic and prokaryotic cells were tested. Collectively, our body of work suggests that by the use of safe nanoadditives we could contribute to reducing the environmental impact of transportation and therein take a positive step towards a more sustainable automotive sector. The workflow proposed here for the evaluation of human and environmental toxicity will allow for the study of nanosized bare graphene material and can be broadly applied to the translation of graphene-based nanomaterials into the market.